Minicom Advanced Systems Smart 4 Betriebsanweisung Seite 61
- Seite / 92
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
To align the mouse pointers
1. On the toolbar, select
The mouse pointers a
li
4.9.3
Calibrating Mouse
A target server
may have a different mouse pointer speed than the
Calibrating automatically discovers the mouse speed of the
the two pointers.
You can perform
automatic
Windows NT4, 2000, or 98.
SmartRack 116 IP
saves this alignment so that calibration is only needed once per
target server.
To
perform the calibration
1. On the toolbar, select
If the Video Noise Level is above zero, calibration may not work. In this case, go to
Video Adjustment and try to eliminate the noise by automatically adjusting the video
(see Section 4.7.2
) and/or adjusting the bars in manual video adjust (see Section
4.7.3
), and then performing the mouse calibration
If the mouse settings on the target server
synchronize mouse pointers manually, as explained below.
4.10
Switching to a
In the middle of a remote session, you can switch to a different server.
To
connect to a different server
1. On the toolbar, click
A list of connected se
r
remote session.
2.
Click the desired server.
The screen of the server terminal emulation window appears.
4.11
Disconnecting the Remote Session
To
disconnect the session
1. On the toolbar, click
The Login Web pag
e appe
Conducting
Switching
To align the mouse pointers
:
> Align (or press Ctrl+M).
li
gn.
Calibrating Mouse
Pointers
may have a different mouse pointer speed than the
client computer
Calibrating automatically discovers the mouse speed of the
target server
automatic
calibration when the target server o
perating system is
Windows NT4, 2000, or 98.
saves this alignment so that calibration is only needed once per
perform the calibration
:
> Calibrate.
If the Video Noise Level is above zero, calibration may not work. In this case, go to
Video Adjustment and try to eliminate the noise by automatically adjusting the video
) and/or adjusting the bars in manual video adjust (see Section
), and then performing the mouse calibration
.
If the mouse settings on the target server
have been
changed, you must
synchronize mouse pointers manually, as explained below.
Switching to a
Different Server
In the middle of a remote session, you can switch to a different server.
connect to a different server
:
.
r
vers appears. There is a checkmark near
the server
Click the desired server.
The screen of the server terminal emulation window appears.
Disconnecting the Remote Session
disconnect the session
:
.
e appe
ars. You can re-login or close the brow
ser
Conducting
a Remote Session
Switching
to a Different Server
User Guide | 61
client computer
.
target server
and aligns
perating system is
saves this alignment so that calibration is only needed once per
If the Video Noise Level is above zero, calibration may not work. In this case, go to
Video Adjustment and try to eliminate the noise by automatically adjusting the video
) and/or adjusting the bars in manual video adjust (see Section
changed, you must
In the middle of a remote session, you can switch to a different server.
the server
of the
ser
window.
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Verwandte Produkte und Handbücher für Vernetzung Minicom Advanced Systems Smart 4
(92 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern